菲尼克斯端子做为完成保护接地的一种零配件产品，与电气设备相接，那么要想更好的使用该产品，就要留意很多的事项。下面来讲讲相关内容吧。

　　Phoenix terminal as a protective grounding of a spare part products, connected with electrical equipment, so in order to better use the product, we must pay attention to a lot of matters. Let's talk about the relevant content.

　　菲尼克斯端子的使用拧紧接线用力要适度，避免用力过将军螺栓螺母扣松，发觉已扣松的螺栓螺母立即拆换，禁止凑合工作。用螺丝起子拧紧或松脱螺母时，务必用力使螺丝起子顶紧螺钉，随后再开展拧紧或松脱，避免螺丝起子与螺钉跑偏，导致螺钉损害不容易拆卸。

　　The use of Phoenix terminal to tighten the wiring force should be moderate, avoid excessive force general bolt and nut buckle loose, found loose bolt and nut immediately disassemble, prohibit casual work. When tightening or loosening the nut with a screwdriver, be sure to tighten the screw with the screwdriver, and then tighten or loosen the screw to avoid deviation between the screwdriver and the screw, resulting in screw damage and not easy to remove.

　　发觉难以拆装的螺栓螺母，不必鲁莽行事，避免导致形变更难以拆装，应提供适度敲击，或加螺丝松动剂、稀硫酸等稍候再开展拆装。不能用老虎钳拧紧或松脱螺栓螺母，防止导致毁坏，用活口扳手时要调节好张口，避免将螺栓螺母毁坏形变，导致不容易拆卸。

　　If you find it difficult to disassemble bolts and nuts, do not act rashly to avoid deformations that are more difficult to disassemble. Moderate percussion should be provided, or screw loosening agent and dilute sulfuric acid should be added to carry out disassembly later. To prevent damage, do not tighten or loosen the bolts and nuts with a vise. When using a adjustable wrench, adjust the opening properly to prevent damage to the bolts and nuts and prevent them from being easily removed.

　　导线连接头或线鼻子相互之间联接时，正中间禁止改装非铜质或导电率能不太好的垫圈。导线连接头联接时，规定接触面积光洁且无空气氧化状况，接线鼻部或铜排相连时，可在触碰表层清洗整洁后擦抹导电膏，随后再开展拧紧。

　　When connecting wire connector or wire nose to each other, it is forbidden to refit non-copper washers or gaskets with poor conductivity in the middle. When connecting the wire connector, the specified contact area should be smooth and free from air oxidation. When connecting the wiring nose or copper bar, wipe conductive paste after cleaning the contact surface, and then tighten it.

　　接临时性线时，单条导线铜线的规定接线头折起来一次，随后收到空气开关下孔；单芯硬线要以“？”型收到空气开关下孔。应用绝缘胶布盘绕电缆线或别的要维护绝缘层的机器设备时，电缆护套应以压置1/2的占比从一端盘绕到另一-端，且少来回一往返。

　　When receiving the temporary line, the stipulated wiring head of a single wire copper wire is folded once, and then the hole under the air switch is received; Single core hard line to “?” Receive air switch under hole. Application of insulation tape winding cable or other equipment to maintain the insulation layer, the cable sheath should be pressed with a ratio of 1/2 from one end winding to the other end, and at least one back and forth.

　　菲尼克斯端子的使用要留意不少的事项就是这样了，当然还有很多注意事项需要大家在使用中多多关注，更多内容就来网站www.jntongyu.com咨询吧。

　　Phoenix terminal use to pay attention to a lot of matters is this, of course, there are a lot of matters needing attention in use, more content to the website www.jntongyu.com consultation.